Slab & Deck 50K & 100K Shoring

50K & 100K Shore Tower System
  • 100K Shoring System - Screw Jack

    Screw Jack (Top)

    Just like the bottom Screw Jacks, top Screw Jacks are adjustable and easy to install. If another tower unit is required, coupler units can be used instead to allow for another tower unit to be stacked and installed on top.

  • 100K Shoring System - Coupler

    Coupler

    Couplers have holes to connect bracing to tower frames. Additionally, Lifting Eyes (LE-5) can be installed to the Coupler allowing for an entire tower unit to be picked by crane and set in place, ready for use.

  • 50K-100K Shoring System Frame Holes

    Adjustable Frame Holes - 50K

    Holes built into the X-Frames allow for varying tower widths. The 50K system can adjust to 6', 7' or 8'.

  • 50K-100K Shoring System Frame Holes

    Adjustable Frame Holes - 100K

    Holes built into the X-Frames allow for varying tower widths. The 100K system can adjust to 8', 9' or 10'.

  • 50K & 100K Shoring System - Welded Frame

    50K Welded Frame

    Each leg can support up to 50,000 lb giving the complete tower unit a capacity of 200,000 lb.

  • 50K & 100K Shoring System - Welded Frame

    100K Welded Frame

    Each leg can support up to 100,000 lb giving the complete tower unit a capacity of 400,000 lb.

  • 50K & 100K - X-Frame

    100K X-Frame

    Adding or changing section units is as simple as removing four pins, sliding the units apart, and pinning the new unit into place. Both the X-Frames and the Welded Frames have a variety of sizes for maximum adjustability.

  • 50K Shoring System Screw Jack

    50K Screw Jack Bottom

    The Screw Jacks are easily attached and adjustable from 11" to 17" for 50K towers. Large foot pads allow for minimum bearing pressure and swivel joints allow for additional adaptability. 50K Screw Jack is a Single Axis Swivel Pivot Jack that is adjustable from 11" – 17"

  • 100K Shoring System Shore Jack

    100K Shore Jack

    The Shore Jacks are 360° Ball Joint Bearing and are easily attached and adjustable from 10" to 16". Large foot pads allow for minimum bearing pressure and swivel joints allow for additional adaptability. For high-load towers, a Sand Jack can be used in conjunction with the Shore Jacks to release the load before cycling. (100K only).

Supportive Slab & Deck Concrete Systems

The EFCO 50K and 100K Shoring Systems are designed to support high and heavy loads on today’s construction projects.

System Setup

For the 50K system, 200K for a complete tower unit, it comes in the basic 8′ x 8′ setup adjustable to 8′ x 7′ or 8′ x 6′. The 100K system has a basic 10′ x 10′ setup providing a complete tower unit with a capacity of 400 K and adjustable to 10′ x 9′ or 10′ x 8′.

Screw jacks on the top and bottom of EFCO Shore Towers provide maximum adjustability. Moving the EFCO Shore Tower is as easy as loosening the screws and picking the entire tower as a single unit. Adding or changing sections is as simple as removing four pins, sliding the units apart and pinning the new unit in place. Consider using the EFCO Shore Tower System when forming high bridge piers, multi-lane bridges, large beams and other heavy loads.

50K Shore Tower

The 50K Shore Towers consist of two welded frames and two (“X”) bracing frames which equal four legs for a maximum load of 200K. Up to four additional legs per tower may be added for a 400K capacity.

100K Shore Tower

100K Shore Towers consist of two welded frames and two (“X”) bracing frames which equal four legs for a maximum load of 400K. Up to four additional legs per tower may be added for a 800K capacity.

previous arrow
next arrow
Slider